dash/doc/cjdns.md

96 lines
3.9 KiB
Markdown
Raw Permalink Normal View History

# CJDNS support in Dash Core
It is possible to run Dash Core over CJDNS, an encrypted IPv6 network that
uses public-key cryptography for address allocation and a distributed hash table
for routing.
## What is CJDNS?
CJDNS is like a distributed, shared VPN with multiple entry points where every
participant can reach any other participant. All participants use addresses from
the `fc00::/8` network (reserved IPv6 range). Installation and configuration is
done outside of Dash Core, similarly to a VPN (either in the host/OS or on
the network router).
Compared to IPv4/IPv6, CJDNS provides end-to-end encryption and protects nodes
from traffic analysis and filtering.
Used with Tor and I2P, CJDNS is a complementary option that can enhance network
redundancy and robustness for both the Dash network and individual nodes.
Each network has different characteristics. For instance, Tor is widely used but
somewhat centralized. I2P connections have a source address and I2P is slow.
CJDNS is fast but does not hide the sender and the recipient from intermediate
routers.
## Installing CJDNS and connecting to the network
To install and set up CJDNS, follow the instructions at
https://github.com/cjdelisle/cjdns#cjdns.
Don't skip steps
["2. Find a friend"](https://github.com/cjdelisle/cjdns#2-find-a-friend) and
["3. Connect your node to your friend's
node"](https://github.com/cjdelisle/cjdns#3-connect-your-node-to-your-friends-node).
You need to be connected to the CJDNS network before it will work with your
Dash Core node.
Typically, CJDNS might be launched from its directory with
`sudo ./cjdroute < cjdroute.conf` and it sheds permissions after setting up the
[TUN](https://en.wikipedia.org/wiki/TUN/TAP) interface. You may also [launch it as an
unprivileged user](https://github.com/cjdelisle/cjdns/blob/master/doc/non-root-user.md)
with some additional setup.
The network connection can be checked by running `./tools/peerStats` from the
CJDNS directory.
## Run Dash Core with CJDNS
Once you are connected to the CJDNS network, the following Dash Core
configuration option makes CJDNS peers automatically reachable:
```
-cjdnsreachable
```
When enabled, this option tells Dash Core that it is running in an
environment where a connection to an `fc00::/8` address will be to the CJDNS
network instead of to an [RFC4193](https://datatracker.ietf.org/doc/html/rfc4193)
IPv6 local network. This helps Dash Core perform better address management:
- Your node can consider incoming `fc00::/8` connections to be from the CJDNS
network rather than from an IPv6 private one.
- If one of your node's local addresses is `fc00::/8`, then it can choose to
gossip that address to peers.
## Additional configuration options related to CJDNS
```
-onlynet=cjdns
```
Make automatic outbound connections only to CJDNS addresses. Inbound and manual
connections are not affected by this option. It can be specified multiple times
to allow multiple networks, e.g. onlynet=cjdns, onlynet=i2p, onlynet=onion.
CJDNS support was added to Dash Core in version 21.0 and there may be fewer
CJDNS peers than Tor or IP ones. You can use `dash-cli -addrinfo` to see the
number of CJDNS addresses known to your node.
In general, a node can be run with both an onion service and CJDNS (or any/all
of IPv4/IPv6/onion/I2P/CJDNS), which can provide a potential fallback if one of
the networks has issues. There are a number of ways to configure this; see
[doc/tor.md](https://github.com/dashpay/dash/blob/master/doc/tor.md) for
details.
## CJDNS-related information in Dash Core
There are several ways to see your CJDNS address in Dash Core:
- in the "Local addresses" output of CLI `-netinfo`
- in the "localaddresses" output of RPC `getnetworkinfo`
To see which CJDNS peers your node is connected to, use `dash-cli -netinfo 4`
or the `getpeerinfo` RPC (i.e. `dash-cli getpeerinfo`).
To see which CJDNS addresses your node knows, use the `getnodeaddresses 0 cjdns`
RPC.