mirror of
https://github.com/dashpay/dash.git
synced 2024-12-24 19:42:46 +01:00
73 lines
2.9 KiB
Markdown
73 lines
2.9 KiB
Markdown
|
# I2P support in Dash Core
|
||
|
|
|
||
|
|
It is possible to run Dash Core as an
|
||
|
|
[I2P (Invisible Internet Project)](https://en.wikipedia.org/wiki/I2P)
|
||
|
|
service and connect to such services.
|
||
|
|
|
||
|
|
This [glossary](https://geti2p.net/en/about/glossary) may be useful to get
|
||
|
|
started with I2P terminology.
|
||
|
|
|
||
|
|
## Run Dash Core with an I2P router (proxy)
|
||
|
|
|
||
|
|
A running I2P router (proxy) with [SAM](https://geti2p.net/en/docs/api/samv3)
|
||
|
|
enabled is required (there is an [official one](https://geti2p.net) and
|
||
|
|
[a few alternatives](https://en.wikipedia.org/wiki/I2P#Routers)). Notice the IP
|
||
|
|
address and port the SAM proxy is listening to; usually, it is
|
||
|
|
`127.0.0.1:7656`. Once it is up and running with SAM enabled, use the following
|
||
|
|
Dash Core options:
|
||
|
|
|
||
|
|
```
|
||
|
|
-i2psam=<ip:port>
|
||
|
|
I2P SAM proxy to reach I2P peers and accept I2P connections (default:
|
||
|
|
none)
|
||
|
|
|
||
|
|
-i2pacceptincoming
|
||
|
|
If set and -i2psam is also set then incoming I2P connections are
|
||
|
|
accepted via the SAM proxy. If this is not set but -i2psam is set
|
||
|
|
then only outgoing connections will be made to the I2P network.
|
||
|
|
Ignored if -i2psam is not set. Listening for incoming I2P
|
||
|
|
connections is done through the SAM proxy, not by binding to a
|
||
|
|
local address and port (default: 1)
|
||
|
|
```
|
||
|
|
|
||
|
|
In a typical situation, this suffices:
|
||
|
|
|
||
|
|
```
|
||
|
|
dashd -i2psam=127.0.0.1:7656
|
||
|
|
```
|
||
|
|
|
||
|
|
The first time Dash Core connects to the I2P router, its I2P address (and
|
||
|
|
corresponding private key) will be automatically generated and saved in a file
|
||
|
|
named `i2p_private_key` in the Dash Core data directory.
|
||
|
|
|
||
|
|
## Additional configuration options related to I2P
|
||
|
|
|
||
|
|
You may set the `debug=i2p` config logging option to have additional
|
||
|
|
information in the debug log about your I2P configuration and connections. Run
|
||
|
|
`dash-cli help logging` for more information.
|
||
|
|
|
||
|
|
It is possible to restrict outgoing connections in the usual way with
|
||
|
|
`onlynet=i2p`. I2P support was added to Dash Core in version 22.0 (mid 2021)
|
||
|
|
and there may be fewer I2P peers than Tor or IP ones. Therefore, using
|
||
|
|
`onlynet=i2p` alone (without other `onlynet=`) may make a node more susceptible
|
||
|
|
to [Sybil attacks](https://en.dash.it/wiki/Weaknesses#Sybil_attack). Use
|
||
|
|
`dash-cli -addrinfo` to see the number of I2P addresses known to your node.
|
||
|
|
|
||
|
|
## I2P related information in Dash Core
|
||
|
|
|
||
|
|
There are several ways to see your I2P address in Dash Core:
|
||
|
|
- in the debug log (grep for `AddLocal`, the I2P address ends in `.b32.i2p`)
|
||
|
|
- in the output of the `getnetworkinfo` RPC in the "localaddresses" section
|
||
|
|
- in the output of `dash-cli -netinfo` peer connections dashboard
|
||
|
|
|
||
|
|
To see which I2P peers your node is connected to, use `dash-cli -netinfo 4`
|
||
|
|
or the `getpeerinfo` RPC (e.g. `dash-cli getpeerinfo`).
|
||
|
|
|
||
|
|
To see which I2P addresses your node knows, use the `getnodeaddresses 0 i2p`
|
||
|
|
RPC.
|
||
|
|
|
||
|
|
## Compatibility
|
||
|
|
|
||
|
|
Dash Core uses the [SAM v3.1](https://geti2p.net/en/docs/api/samv3) protocol
|
||
|
|
to connect to the I2P network. Any I2P router that supports it can be used.
|