Previously the minRelayTxFee was only enforced on user specified values.
It was possible for smartfee to produce a fee below minRelayTxFee which
would just result in the transaction getting stuck because it can't be
relayed.
This also introduces a maxtxfee option which sets an absolute maximum
for any fee created by the wallet, with an intention of increasing
user confidence that the automatic fees won't burn them. This was
frequently a concern even before smartfees.
If the configured fee policy won't even allow the wallet to meet the relay
fee the transaction creation may be aborted.
Rebased-From: aa279d6131
Github-Pull: #5485
There are 3 pieces of data that are maintained on disk. The actual block
and undo data, the block index (which can refer to positions on disk),
and the chainstate (which refers to the best block hash).
Earlier, there was no guarantee that blocks were written to disk before
block index entries referring to them were written. This commit introduces
dirty flags for block index data, and delays writing entries until the actual
block data is flushed.
With this stricter ordering in writes, it is now safe to not always flush
after every block, so there is no need for the IsInitialBlockDownload()
check there - instead we just write whenever enough time has passed or
the cache size grows too large. Also updating the wallet's best known block
is delayed until this is done, otherwise the wallet may end up referring to an
unknown block.
In addition, only do a write inside the block processing loop if necessary
(because of cache size exceeded). Otherwise, move the writing to a point
after processing is done, after relaying.
Previously -proxy was not setting the proxy for IsLimited networks, so
if you set your configuration to be onlynet=tor you wouldn't get an
IPv4 proxy set.
The payment protocol gets its proxy configuration from the IPv4 proxy,
and so it would experience a connection leak.
This addresses issue #5355 and also clears up a cosmetic bug where
getinfo proxy output shows nothing when onlynet=tor is set.
This is a simplified re-do of closed pull #3088.
This patch eliminates the privacy and reliability problematic use
of centralized web services for discovering the node's addresses
for advertisement.
The Bitcoin protocol already allows your peers to tell you what
IP they think you have, but this data isn't trustworthy since
they could lie. So the challenge is using it without creating a
DOS vector.
To accomplish this we adopt an approach similar to the one used
by P2Pool: If we're announcing and don't have a better address
discovered (e.g. via UPNP) or configured we just announce to
each peer the address that peer told us. Since peers could
already replace, forge, or drop our address messages this cannot
create a new vulnerability... but if even one of our peers is
giving us a good address we'll eventually make a useful
advertisement.
We also may randomly use the peer-provided address for the
daily rebroadcast even if we otherwise have a seemingly routable
address, just in case we've been misconfigured (e.g. by UPNP).
To avoid privacy problems, we only do these things if discovery
is enabled.
This is less surprising.
Avoids the overload-the-CPU default of using N threads for script
verification as well as N threads for generation where N is number of cores.
Start the RPC server before doing all the (expensive) startup
initialisations like loading the block index. Until the node is ready,
return all calls immediately with a new error signalling "in warmup"
with an appropriate status message (similar to the init message).
This is useful for RPC clients to know that the server is there (e. g.,
they don't have to start it) but not yet available. It is used in
Namecoin and Huntercoin already for some time, and there exists a UI
hooked onto the RPC interface that actively uses this to its advantage.
a873823 CAutoFile: Explicit Get() and remove unused methods (Wladimir J. van der Laan)
fef24ca Add IsNull() to class CAutoFile and remove operator ! (Ruben Dario Ponticeli)
c0195b1 Bugfix: Remove default from -zapwallettxes description (inaccurate) (Luke Dashjr)
0a08aa8 Parameterise command line option defaults, so translations are independent of them (Luke Dashjr)
Previous refactorings broke the ability to rebuild the chainstate by deleting the chainstate
directory, resulting in an incorrect "Incorrect or no genesis block found" error message. Fix
that.
Also, improve the performance of ActivateBestBlockStep by using the skiplist to only discover
a few potential blocks to connect at a time, instead of all blocks forever - as we likely bail
out after connecting a single one anyway.
7c70438 Get rid of the dummy CCoinsViewCache constructor arg (Pieter Wuille)
ed27e53 Add coins_tests with a large randomized CCoinViewCache test. (Pieter Wuille)
058b08c Do not keep fully spent but unwritten CCoins entries cached. (Pieter Wuille)
c9d1a81 Get rid of CCoinsView's SetCoins and SetBestBlock. (Pieter Wuille)
f28aec0 Use ModifyCoins instead of mutable GetCoins. (Pieter Wuille)
- explicit init of pcoinsdbview and pwalletMain (even if not needed, as
globals are init to NULL, it seems cleaner)
- remove check if (pwalletMain) in Shutdown() as delete is valid even if
pwalletMain is NULL
Always make a pid file, not only when `-daemon` specified.
This is useful for troubleshooting, for attaching debuggers and loggers
and such.
- Write the pid file only after the datadir lock was acquired
- Don't create or remove a pid file on WIN32, and also don't show the option
There is no reason to store thousands of orphan transactions;
normally an orphan's parents will either be broadcast or
mined reasonably quickly.
This pull drops the maximum number of orphans from 10,000 down
to 100, and adds a command-line option (-maxorphantx) that is
just like -maxorphanblocks to override the default.
