mirror of
https://github.com/dashpay/dash.git
synced 2024-12-27 04:52:59 +01:00
96 lines
3.9 KiB
Markdown
96 lines
3.9 KiB
Markdown
# CJDNS support in Dash Core
|
|
|
|
It is possible to run Dash Core over CJDNS, an encrypted IPv6 network that
|
|
uses public-key cryptography for address allocation and a distributed hash table
|
|
for routing.
|
|
|
|
## What is CJDNS?
|
|
|
|
CJDNS is like a distributed, shared VPN with multiple entry points where every
|
|
participant can reach any other participant. All participants use addresses from
|
|
the `fc00::/8` network (reserved IPv6 range). Installation and configuration is
|
|
done outside of Dash Core, similarly to a VPN (either in the host/OS or on
|
|
the network router).
|
|
|
|
Compared to IPv4/IPv6, CJDNS provides end-to-end encryption and protects nodes
|
|
from traffic analysis and filtering.
|
|
|
|
Used with Tor and I2P, CJDNS is a complementary option that can enhance network
|
|
redundancy and robustness for both the Dash network and individual nodes.
|
|
|
|
Each network has different characteristics. For instance, Tor is widely used but
|
|
somewhat centralized. I2P connections have a source address and I2P is slow.
|
|
CJDNS is fast but does not hide the sender and the recipient from intermediate
|
|
routers.
|
|
|
|
## Installing CJDNS and connecting to the network
|
|
|
|
To install and set up CJDNS, follow the instructions at
|
|
https://github.com/cjdelisle/cjdns#cjdns.
|
|
|
|
Don't skip steps
|
|
["2. Find a friend"](https://github.com/cjdelisle/cjdns#2-find-a-friend) and
|
|
["3. Connect your node to your friend's
|
|
node"](https://github.com/cjdelisle/cjdns#3-connect-your-node-to-your-friends-node).
|
|
You need to be connected to the CJDNS network before it will work with your
|
|
Dash Core node.
|
|
|
|
Typically, CJDNS might be launched from its directory with
|
|
`sudo ./cjdroute < cjdroute.conf` and it sheds permissions after setting up the
|
|
[TUN](https://en.wikipedia.org/wiki/TUN/TAP) interface. You may also [launch it as an
|
|
unprivileged user](https://github.com/cjdelisle/cjdns/blob/master/doc/non-root-user.md)
|
|
with some additional setup.
|
|
|
|
The network connection can be checked by running `./tools/peerStats` from the
|
|
CJDNS directory.
|
|
|
|
## Run Dash Core with CJDNS
|
|
|
|
Once you are connected to the CJDNS network, the following Dash Core
|
|
configuration option makes CJDNS peers automatically reachable:
|
|
|
|
```
|
|
-cjdnsreachable
|
|
```
|
|
|
|
When enabled, this option tells Dash Core that it is running in an
|
|
environment where a connection to an `fc00::/8` address will be to the CJDNS
|
|
network instead of to an [RFC4193](https://datatracker.ietf.org/doc/html/rfc4193)
|
|
IPv6 local network. This helps Dash Core perform better address management:
|
|
- Your node can consider incoming `fc00::/8` connections to be from the CJDNS
|
|
network rather than from an IPv6 private one.
|
|
- If one of your node's local addresses is `fc00::/8`, then it can choose to
|
|
gossip that address to peers.
|
|
|
|
## Additional configuration options related to CJDNS
|
|
|
|
```
|
|
-onlynet=cjdns
|
|
```
|
|
|
|
Make automatic outbound connections only to CJDNS addresses. Inbound and manual
|
|
connections are not affected by this option. It can be specified multiple times
|
|
to allow multiple networks, e.g. onlynet=cjdns, onlynet=i2p, onlynet=onion.
|
|
|
|
CJDNS support was added to Dash Core in version 21.0 and there may be fewer
|
|
CJDNS peers than Tor or IP ones. You can use `dash-cli -addrinfo` to see the
|
|
number of CJDNS addresses known to your node.
|
|
|
|
In general, a node can be run with both an onion service and CJDNS (or any/all
|
|
of IPv4/IPv6/onion/I2P/CJDNS), which can provide a potential fallback if one of
|
|
the networks has issues. There are a number of ways to configure this; see
|
|
[doc/tor.md](https://github.com/dashpay/dash/blob/master/doc/tor.md) for
|
|
details.
|
|
|
|
## CJDNS-related information in Dash Core
|
|
|
|
There are several ways to see your CJDNS address in Dash Core:
|
|
- in the "Local addresses" output of CLI `-netinfo`
|
|
- in the "localaddresses" output of RPC `getnetworkinfo`
|
|
|
|
To see which CJDNS peers your node is connected to, use `dash-cli -netinfo 4`
|
|
or the `getpeerinfo` RPC (i.e. `dash-cli getpeerinfo`).
|
|
|
|
To see which CJDNS addresses your node knows, use the `getnodeaddresses 0 cjdns`
|
|
RPC.
|